Torlon Polyamideimide Materials Data Sheet

||Torlon Polyamideimide Materials Data Sheet
Torlon Polyamideimide Materials Data Sheet2018-02-16T12:06:09+00:00

Torlon Polyamideimide Materials are thermosetting or thermoplastic amorphous polymers that have exceptional mechanical, thermal and chemical resistant properties.

Torlon 4503 Torlon 4203 Torlon 4203L Torlon 4501 Torlon 4301 Torlon 4301 Torlon 5530 Torlon 5030
Mechanical ASTM Test Method Compression Molded Polyamideimide Extruded Polyamideimide Injection Molded Polyamideimide Compression Molded Bearing Polyamideimide Extruded Bearing Grade Polyamideimide Injection Molded Bearing Polyamideimide Compression Molded 30% Glass-filled Polyamideimide Injection Molded 30% GF Polyamideimide Units
Strength to Weight Ratio - - - - - - - - - ksi
Specific Gravity @73 F D792 1.40 1.41 1.41 1.45 1.45 1.45 1.61 1.60 -
Tensile Strength @73 F, (ult)/(yld) D638 18,000 (ult) 18,000 (ult) 22,000 (ult) 10,000 (ult) 12,000 (ult) 19,000 14,000 (ult) 24,000 (ult) psi
Tensile Modulus of Elasticity @73 F D638 500,000 600,000 600,000 440,000 900,000 760,000 500,000 1,200,000 psi
Tensile Elongation at Break @73 F D638 5 5 15 3 3 7 3 4 %
Flexural Strength @73 F D790 24,000 24,000 28,000 20,000 31,000 25,000 20,000 36,000 psi
Flexural Modulus of Elasticity @73 F D790 600,000 600,000 700,000 650,000 1,000,000 750,000 800,000 1,000,000 psi
Shear Strength @73 F D732 - 16,000 15,000 - 16,400 13,000 - 24,500 psi
Comprehensive Strength, (% Deformation) @73 F D695 17,000 (10) 28,000 (10) 32,000 (10) 18,000 (10) 24,000 (10) 24,000 (10) 18,000 (10) 38,000 (10) psi
Comprehensive Modulus of Elasticity @73 F D695 350,000 700,000 700,000 350,000 950,000 950,000 350,000 600,000 psi
Hardness, Rockwell, Scale as noted @73 F D785 M119 (E80) M120 (E80) M120 (E80) M106 (E70) M106 (E70) M106 (E70) M120 (E77) M125 (E77) -
Hardness, Durometer, Shore D @73 F D2240 D90 - - D90 - - D90 - -
Izod Impact, (Notched) @73 F D256 Type A 1.5 2.0 2.5 0.5 0.8 1.1 0.7 1.3 ft-lb/in of notch
Coefficient of Friction, (Dry vs Steel) Dynamic - 0.30 0.27 0.35 0.20 0.20 0.20 0.20 0.19 -
Limiting PV, (with 4 to 1 factor of safety applied) - - 17,500 - 22,500 22,500 30,000 20,000 - psi-ft/min
Thermal ASTM Test Method Compression Molded Polyamideimide Extruded Polyamideimide Injection Molded Polyamideimide Compression Molded Bearing Polyamideimide Extruded Bearing Grade Polyamideimide Injection Molded Bearing Polyamideimide Compression Molded 30% Glass-filled Polyamideimide Injection Molded 30% GF Polyamideimide Units
Coefficient of Linear Thermal Expansion @73 F E-831 (TMA) 1.5 E-05 1.7 E-05 1.7 E-05 2.0 E-05 1.4 E-05 1.4 E-05 2.5 E-05 1.0 E-05 in/in/F
Heat Deflection Temperature @264 psi D648 532 532 532 534 534 534 520 539 F
Tg-Glass transition termperature, (Amorphous) D3418 527 527 527 527 527 527 527 527 F
Melting Point, (VS=Vicat Softening Temp.) D3418 - - - - - - - - F
Continuous Service Temperature in Air, (Max.) - 500 500 500 500 500 500 500 500 F
Thermal Conductivity - 1.80 1.80 1.80 3.70 3.7 3.70 2.50 2.50 BTU-in /
hr-ft2-F
Electric ASTM Test Method Compression Molded Polyamideimide Extruded Polyamideimide Injection Molded Polyamideimide Compression Molded Bearing Polyamideimide Extruded Bearing Grade Polyamideimide Injection Molded Bearing Polyamideimide Compression Molded 30% Glass-filled Polyamideimide Injection Molded 30% GF Polyamideimide Units
Dielectric Strength, Short Term D149 580 580 580 - - - 700 840 Volts/mil
Volume Resistivity D257 2.0 E+17 2.0 E+17 2.0 E+17 8.0 E+15 3.0 E+15 8.0 E+15 2.0 E+17 2.0 E+17 ohm-cm
Dielectric Constant @10E6 Hz D150 3.9 3.9 3.4 5.4 6.0 5.4 6.3 6.5 -
Dissipation Factor @10E6 Hz D150 0.031 0.031 0.031 0.042 0.037 0.042 0.220 0.023 -
Flammability @3.1 mm unless noted UL94 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 -
H2O ASTM Test Method Compression Molded Polyamideimide Extruded Polyamideimide Injection Molded Polyamideimide Compression Molded Bearing Polyamideimide Extruded Bearing Grade Polyamideimide Injection Molded Bearing Polyamideimide Compression Molded 30% Glass-filled Polyamideimide Injection Molded 30% GF Polyamideimide Units
Water Absorption, Immersion, 24 hours D570(7) 0.35 0.40 0.33 0.30 0.28 0.28 0.03 0.30 % by weight
Water Absorption, Saturation D570(7) 1.70 1.70 1.70 1.50 1.50 1.50 1.50 1.50 % by weight